K-Edge | Integrated Handlebar System Bicycle Computer Mount | for Wahoo GPS Devices | Black

I bough this so I could mount my GPS and light and so far so good! The only issue was the mounting screws were not correct and this is made clear on the K-Edge website. However, the website told me what I needed from the hardware store to make it work - M4x20mm 0.7 thread pitch. It is now installed and working well.

I attached this mount to my Canyon Ultimate with CP10 cockpit and it looks and works great. I scoured the internet looking for alternate solutions to mount my Wahoo ELEMNT (original version) and didn't find anything that really pleased me, so I bought this. If I'm being nitpicky, I do wish they would have toned down the branding on the side a bit as I felt like it may take away from the look I was going for. Glad that my computer basically hides the mount away underneath. I also wish that K-Edge would've included a greater variety of screws and maybe some washers, but a quick trip to the hardware store solved that for me. I did have an issue on my first ride with the vibrations of the handlebars causing the screws to fall out, despite having added threadlock. My LBS advised me to add a split ring washer and I haven't had any issues since.TL;DR: it's a decent mount. make sure you have the right bolts for your bike and consider adding a split ring washer and threadlock.

I added this mount to my Canyon Grail with CP07 handlebars after visiting the hardware store to by two M4 - 0.7 x 16mm bolts and a pack of M4 washers. It was about 2 extra dollars. After that the mount went on easily and stayed put during a bumpy gravel ride. The build quality seems nice and I was ok paying a bit more since it's made in the USA. I have yet to use the underside mount but will be adding a light there.

At first I thought it was kind of pricey until I received it. Compared to my previous with no adjustability, I can definitely see the craftsmanship in the K-edge. The bottom of my handlebar sloped my bike computer up at an angle. K-edge adjustability allows my bike computer to sit horizontal with my handlebars. Also the undermount allows my light to sit further back. I should’ve bought this product the first time instead of wasting $20 shm

This is a very needed product to hold your Garmin/Wahoo/other cycling computer (Hammerhead) to handlebars that only have the two screws on the bottom. For a Canyon CP07 Aero handlebar, the two screws included with the K-Edge mount DO NOT FIT; you need thinner screws. This is annoying; luckily for me, I had some thinner screws so it worked for me but you may have to go to a local Home Depot.The other important part of this mount is the holder for a light; this mount effectively holds your computer AND your light (I use a NiteRider and it works perfectly).I like the adjustment you can make to tilt the mount; it's a nice touch.This is a good product and I recommend this over the cheaper (made in China) products.CP07

Please note this product failed on the very first time it was used. I had attached the Garmin light UT 800 and the Garmin 1030 computer on top. It was attached to the handlebar through the two holes at the very end as specified by the diagram supplied. However, after approximately 28 miles it broke luckily I always use the bungee cord for the Garmin 1030 to hold to the handlebar. My first thought was to return it but my bike technician was able to fabricate it by drilling a hole and utalize the other holes closer to the front of the product. Just a reminder that this product need to be reconfigured in respect the material for construction.

This perfectly fits my Canon Grail. It's stable, yet lightweight, a solid upgrade from the plastic mount I previously had on the bike.One downside is that the built-in mount on the GoPro Hero 9 is too small to fit in the mount without swinging around. If you have a GoPro, plan to put some washers in when you mount it.

Buy this first and save the grief of the China knockoffs. 3 broke before I bought the K Edge. Penny wise stupid.4 stars because I haven't tried the go pro mount

Preis Leistung ist ok, ist nur etwas kompliziert die DI2 Einheit am Halter zu fixieren, ein Gamin 1000 passt nicht

The M5 screw does not fit the Canyon CP10 cockpit. M4 screw with washer is required to fit the mount. Expensive for a mount that does not work as well.

Resistente. Fiable.

Works as advertised and is solid and well made. Worth the premium over cheaper mounts.

Screw not compatible and not easy to find in my regionReturn the product