Mowei [3-Pack] MOWEI for Galaxy S22 Ultra Screen Protector [Fully Support Fingerprint & S Pen] 3D Curved Tempered Glass for Samsung S22 Ultra 5G [Scratch & Impact Protection]

Update: after seven months on my phone this protector just saved my screen from a major drop. The phone fell about five feet face down onto stony tarmac, followed by my foot! The screen protector was trashed. The phone screen has not got a mark on it. Best hardened glass protector I've had.The bad bit first: this is not a simple screen protector to fit. I'm used to films, dry and wet lay, tempered glass, "air" glass etc. I've never had to use a UV cured glue before. It takes time, patience and care to get it right. Watch the instruction video and, preferably, someone else's video too. The glue can be really slow to fully spread under the protector, BE PATIENT! And, because it's UV cured and it can take a while, I'd close the curtains just in case. Once you switch on the UV the initial cure is really fast, and then you're stuck. It's a bit of a faff, and I screwed up the first protector being impatient.Now the good bits:Of all of the curved screen protectors I've used this is the closest fit of any glass I've used. In my case there's hardly any gap at all.The oleophobic coating, and the feel of the screen, is very close to the bare glass. It's really good.Generally I find tempered glass protectors, especially on curved screens, really easy to crack. I've had no such issue with this protector, it seems very robust (touch wood).The fingerprint detection is excellent. (Note: I left my old prints in the system to try them, and they worked, but I did delete them and register new ones after that test). Print recognition is fast and doesn't take any extra pressure.Basically, after the pain of fitting, it feels like I'm working on the bare screen.

I've been using resin screen protectors for years and this the first time I've seen this problem. At first the application looks perfect but within the next few days the screen protector delaminates in this strange ugly pattern that's impossible to ignore. I have tried 2/3 of the screen protectors in the pack and they both do the same thing and yes I watched the video carefully. As other reviews have said, you start off with no air bubbles then one forms in the middle and slowly gets bigger until the screen protector is ruined within a few days.This type of protector normally lasts me 6 months to a year so it's been a massive waste of money for me. The only time I've seen a similar issue was with a tempered glass screen protector sold for s22 ultras but actually made for s23 ultra. The dimensions are similar but one has a more shallow curve. I suspect that's the issue here otherwise normally with resin, if there are bubbles they stay where they are. They don't slowly get bigger until the screen protector falls off because the resin hardens during the application process so air shouldn't get in unless there's something wrong with the screen protector itself.The screen protector eventually cracked where the air bubble formed and left tiny scratches on my screen.

Never used this type of screen protector before but after spending 1300 quid on a phone I wanted a bit more than a plastic film on there.This fits spot on, the install is not bad, watch the video a few times first and I took an extra sticker from an old protector kit and covered the buttons on the side and the microphone slit at the top just to make sure no glue got in there.Went on perfect, one small bubble so lifted it again slightly and lowered back all good. Cure with the light and the weight on the finger print sensor and job jobbed.Bit of clean if on the sides of the phone but it comes off with your fingernail.So far,1/2 a day it is perfect Clear, feels great super smooth. It still worked with my finger prints but I un registered them anyway and did them again. As far as I can tell its just as quick as it was before.As for fitting in a case, I have the UB supcase as I work in a fairly rugged environment so like the added protection. The top bottom and sides meet up exactly with the frame on the case. It's just the very corners that are under the frame. No issue so far so will see how it lasts. And you get 3 so it's not the end of the world if you mess 1 up.Overall very happy for the price.

This is some work to install and there's more scope to get it wrong than the flat glass screen protectors, but if you want a curved glass protector I couldn't find an alternative.The kit includes everything you need, the instructions are good and clear, but the process is fiddly. Base on the advice of another reviewer, I didn't use their weight for the fingerprint reader, instead I alternately pressed firmly with my thumb and hit the screen with the UV lamp for 10 secs a few times. I also went rouge and tried only adding half the glue in the first place, to achieve a thinner layer. I got away with this and the fingerprint reader works well. I did have to mop up a little glue squeeze-out, I did this during during curing.Once applied, I'm 80-90% happy. The glass is not perfectly flat, so reflections on a black screen have a slight wobble, but that has no effect on use. I do have a couple of air bubbles in the middle of my screen, they're tiny but can be seen on mostly plain, light coloured screens. I rarely notice them. This is always an issue with screen protectors, it's down to you when applying it and I have the materials to replace it twice if it bugs me.I was hesitant to buy with the cost and mixed reviews, but this is a good product and I'd buy it again if needed.