Electrically Conductive Wire Glue

Used to repair some rubber contact pads that the carbon had worn down on. Worked great!

Yes given a conductive low voltage connection. And the recommended super glue suggestion on its shipping carton was a good addon precaution to secure for rough us, as in my case (game battery side ground spring).

A connection came loose on the rear window defroster on my car. I soldered it a couple times but it's in such an awkward position, I couldn't get enough solder on it to hold for any length of time.I thought if this Wire Glue worked as advertised, it would be just the thing. I followed directions to the letter but had a hard time getting it to hold. It finally set with a piece of tape holding the glued connection in place. After 24 hours I removed the tape and the connection held but when I turned the defroster on, the connection arced. It's still holding but just enough to cause electrical interference in my stereo. The defroster won't work. I guess I'll have to take it loose and get the soldering gun back out. Don't waste your money on this stuff.

Glue is probably the wrong word for this product. I was able to use it to "glue" a component back on and it did conduct electricity. I tried "glueing" a wire to a pad and couldn't get it to hold. Glue is thin and doesn't stick well. It seems to work well in limited applications. The advice in the instructions dto back this up with super glue should probably be followed.

It's A Mixture of Graphite & Water Soluble GlueComes with lots of caveats so do some research...like it won't work to fix any kind of wiringattached to a windshield, antenna, defroster etc.It isn't tacky.. so either use a clamp, or beprepared to hold the object (for a long time.)It's thin & watery..apply sparingly in layers....and even after it's dried to the touch, itwon't conduct electricity very well until it'ssat for at least a few days to throughly dry.It gets Brittle.. and will crack away under anykind of stress or tugging.. so be prepared toreinforce whatever you're mending with eithertape of an additional application of epoxy.Lastly... It's NOT really Metallic.. IOW.. Notas good at conducting electricity as you'dprobably hope it would be. It DOES conduct acurrent but not as well as solder. I fixed aflashlight, and you can see a BIG differencebetween the mended flash & an identical unit.Given the alternative (buying and/or using asoldering unit) it's BETTER THAN NOTHING.

The media could not be loaded. The glue is very thin and watery, but I was able to use it to secure a wire to a terminal that was too close to a plastic case for soldering. The important thing is to make sure the wire is firmly touching the terminal before applying the glue. I used the wire's own tension to make sure it would stay against the terminal while the glue dried. Instructions recommend leaving it overnight, but I applied low heat to get it to dry and found it had firmed up after a couple hours.Per suggestion in the instructions, I added a layer of epoxy over top of the glue to assure that the wire wouldn't work loose.

I bought this "glue" to attach spade connectors to each end of a battery. The spade was a male connector (basically a flat strip). The product is the consistency of paint not glue. there was no tacky to it, so the tab needed to be clamped in place until it dried. After 24 hours the paint was dry, but it had no strength. When I tested it, the tab fell off, so I cleaned it and reattached it. After the 24 hours I super glued it as recommended in the instructions. After that dried, I checked and there was no continuity across the connection. Thinking there was an issue, I pulled it apart again with very little effort. This time not only did I need to clean off the paint, but also the super glue. After several more tries varying the pressure of the clamp to attempt a spot that would have metal to metal contact around the paint and still be somewhat stronger bond, I decided that there was a tradeoff. I was either going to have a structural bond or an electric bond but not both. It would seem that this product may work on a circuit board where there is a good physical contact but no need for strength

I have a group of 6, 12V outdoor lighting group of lights that enhance our front gardens around our house. On one of the light connections, one of the two wires pulled out of the plastic housing (the electrical connection was down a small hole in the plastic housing. The wire had just pulled out exposing the metal strands of wire. When I pushed the wire back into the hole, the light lit up again, but the wire would not stay inside of the hole. I knew it needed to be soldered....somehow, but with no exposure to the connecting point inside of the plastic housing it was impossible. After a bit of googling and YouTubing, I found this product which was highly recommended. I searched on Amazon, found it, ordered it, it came quickly. I put some of the wire glue on the wires and dropped a bunch down the hole, jammed the wire into the hole (the light came on), I held the wires in place for a few minutes, and after a few months of various weather (warm, wet, cold, etc) the light still works. Great product!